亚洲一区亚洲二区人妻-日日摸夜夜添毛片性色av-国产又大又长又粗视频-男女激情免费视频网站

　　Working principle of crusher:

　　1. Working principle of the heavy hammer crusher: the motor drives the rotor to rotate at high speed in the crushing chamber, and the materials are fed into the crusher from the upper feeding port, and crushed by the impact, impact, shearing and grinding of the high-speed moving hammer.

　　In the lower part of the rotor, there is a sieve plate, and the particles smaller than the size of the sieve hole are discharged through the sieve plate. The coarse particles larger than the size of the sieve hole are retained on the sieve plate and continue to be hit and ground by the hammer. Finally, they are discharged from the outside of the crusher through the sieve plate.

　　2. Working principle of impact crusher: when the machine is working, driven by the motor, the rotor rotates at high speed. When the material enters into the action area of plate hammer, it collides with the plate hammer on the rotor to break.

　　It is thrown to the counterattack device to break again, and then it bounces back from the counterattack lining plate to the action area of the plate hammer to break again. This process is repeated.

　　From large to small, the material enters the first, second and third reaction chambers for repeated crushing until it is crushed to the required particle size and discharged from the discharge port. Adjusting the gap between the reaction frame and the rotor can change the size and shape of the material.

　　How to maintain the lubrication system of crusher

　　Good equipment plus good operation and maintenance can bring good benefits to production, while maintenance only means to reduce the failure of equipment in the work and ensure its smooth production process, such as lubrication operation. However, there are many problems that need attention when lubrication is in progress. Only good lubrication can ensure the smooth operation of equipment. Here Is to introduce, crusher in lubrication, need to pay attention to the problem.

　　Note 1: the crusher can be started only after the lubricating system is running and the lubricating oil returns to the oil storage tank.

　　Note 2: pay attention to the temperature rise of lubricating oil. Whether in winter or summer, the return oil temperature of lubricating oil must be between 39 ℃ - 54 ℃. In this case, it is necessary to select the appropriate type of lubricating oil to ensure the good operation process of crusher. In winter, it is necessary to drain the water in the cooler when parking to prevent solidification.

　　Note 3: if the filter in the crusher is put into use for the first time, the liquid leakage test shall be carried out. When the valve is opened or closed to control the flow of lubricating oil through the filter in production, it is necessary to prevent the pipeline of the lubrication system from liquid hammer. In production, in order to ensure the efficiency of the filter, when the pressure difference between the inlet and outlet of the filter reaches 138kpa, it must be replaced Filter element.

　　Note 4. In the production of crusher, do not disconnect the power supply of alarm device such as resistance temperature detector and pressure transmitter. If the lubricating pump device needs to be disassembled, all the pressure in the pump needs to be discharged before operation. Note 5: different weather conditions have a great impact on the crusher's work, so different lubricants should be selected according to different seasons. In hot summer, higher viscosity lubricants should be selected, but in cold winter, lower viscosity lubricants should be selected. Of course, the specific requirements of the manufacturer should be referred to when selecting.

　　Note 6. When the crusher is working, the oil supply pressure of its lubricating oil should be controlled within the range of 0.08-0.2mpa. Otherwise, it will cause great impact on production. For example, if the oil supply pressure is small, it will cause that the lubricating oil fails to reach the corresponding lubricating parts due to insufficient power, and the lubricating effect will not be achieved. If the oil pressure is too large, it will cause the eccentric sleeve of the crusher This phenomenon makes the top of the big gear and the bottom of the bowl shaped tile seat contact and cause mutual wear. If it is serious, it will bring up the straight bushing and cause the straight bushing to break.

　　Note 7: since lubrication has a great influence on the efficiency and service life of crusher, in order to ensure the effect of lubrication, the lubrication system and crusher can be electrically interlocked. Before starting the machine, the oil pump must be turned on first, otherwise the motor cannot be started. When the oil pump stops or the oil pressure drops to 0.05Mpa, signals will be sent out to stop the motor operation to ensure the crusher The machine parts of are not damaged, ensuring their service life.

　　Select the equipment for oil filter of crusher lubrication system:

　　The multi-functional vacuum oil filter produced by Zhongjing filtration equipment manufacturing Co., Ltd. of our company is used in machinery, metallurgy, mining, petroleum, chemical industry and other fields to purify hydraulic oil, mechanical oil, cooling oil, refrigeration oil, gear oil, gasoline oil, diesel oil, heat treatment oil and other lubricating oil. It can quickly remove water, impurities, volatiles (such as ammonia) and other harmful components in the oil, improve the quality of the oil and restore its service performance. Ensure the normal operation of hydraulic system, power system and lubrication system. Special filter and purification equipment for lubricating oil is used for dehydration and purification of mechanical impurities!